Analytical Technology A15 Especificações Página 27
- Página / 32
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ATI A15/76 Turbidity Monitor Part 6 – Operation
27
O&M Manual
Rev-H (8/11)
Controls & Alarm Outputs
The A15/76 Turbidity Monitor is equipped with three relay outputs. Two of these outputs are
designated control relays and the third is designated as an alarm relay. These output relays may be used
in a variety of ways, and the function of each relay is programmable by the operator. Relay output wiring
is made at the rear of the monitor as shown in the diagram on page 14.
Control Relays
The relays designated control relays may be used for either alarm functions or control functions.
Each of the two relays is SPDT with a 220 VAC 5A resistive contact rating. Each control relay can be
programmed as either a high or a low alarm, and the hysteresis and time delay can also be set.
To program control relays, proceed as follows:
1. Press the MODE key until SA appears on the left side of the display. The full display will indicate
"SA X.XXmS oLO" This refers to setpoint A and indicates the current setting for control relay A.
X.XX is the current setpoint, o(or n) indicates the current status of the relay, and LO(or HI)
indicates a low or high alarm function.
2. Press the CAL key once and the display will read "CAL SA S: X.XX". The value of X.XX is the
setpoint for that relay. Use the UP and DOWN keys to adjust the value to the desired setpoint.
Then press the ENTER key.
3. The display will now read "CAL SA I: 0.00". I is the setpoint hysteresis or deadband for that relay.
Use the UP and DOWN keys to adjust the deadband to the desired value. A value of at least
0.2% of display range is recommended to avoid relay cycling at the actuation point. The
maximum setting is 10% of the display range selected in configuration. When the value is set,
press the ENTER key.
4. The display will now read "CAL SA D: 0.0s". D is the delay time for relay actuation. Use the UP
and DOWN keys to select the desired delay time in seconds. The maximum delay time is 99.9
seconds. When the selection is made, press the ENTER key.
5. The display will return to the original "SA X.XXmS oLO". Press the MODE key to access the "SB
X.XXmS oLO" display.
6. The steps outlined in 1-4 above should be repeated for SB to program operation of relay B.
Alarm Relay
The Turbidity Monitor also contains a relay designated as an alarm relay. This relay may be used
to warn of various conditions that might indicate operational problems. The relay will activate on either
high or low turbidity conditions, and can be used to indicate failure of the control relays to maintain proper
control. This relay is designated "C" on the wiring schematic, and the function of the relay with respect to
its association with relays A and B is covered in the Configuration section of this manual.
- Model A15/76 1
- PRODUCT WARRANTY 2
- TABLE OF CONTENTS 3
- TABLE OF FIGURES 4
- Unpacking 5
- Part 1 - Introduction 6
- Specifications 7
- Electronics Unit 7
- SIDE VIEWFRONT VIEW 8
- DC Powered Monitor 17
- Part 4 – Start-Up 19
- Front Panel Lock 20
- Part 5 - Configuration 21
- Part 6 - Operation 24
- Setting Sensitivity (Span) 25
- Controls & Alarm Outputs 27
- Analog Output Adjustment 28
- Simulate Mode 29
- Check Signal Display 30
- Part 7 - Maintenance 31
- SPARE PARTS LIST 32
Manuais e produtos relacionados com Medição, teste e controlo Analytical Technology A15
Philips SPS1541WA-17 manuály
Uživatelské manuály a uživatelské příručky pro Příslušenství pro video Philips SPS1541WA-17.
Poskytujeme 1 manuály pdf Philips SPS1541WA-17 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Philips SPS1541WA-17 Uživatelský manuál (2 strany)
Značka: Philips | Kategorie: Accessories for video | Velikost: 0.21 MB |
Tabulka s obsahem
Další produkty a příručky pro Příslušenství pro video Philips
| Modely | Typ Dokumentu |
|---|---|
| SPP3060J-17 |
Uživatelský manuál
Philips SPP3060J-17 User Manual,
2 stránky
|
| Sync & Charge Cable DLC2407 for iPhone & i |
Uživatelský manuál
Philips Sync & Charge Cable DLC2407 for iPhone & iPod User Manual,
2 stránky
|
| DLM1662-17 |
Uživatelský manuál
Philips DLM1662-17 User Manual,
2 stránky
|
| SWA3102W-17 |
Uživatelský manuál
Philips SWA3102W-17 User Manual,
2 stránky
|
| SDJ8040W-17 |
Uživatelský manuál
Philips SDJ8040W-17 User Manual,
2 stránky
|
| DLP2280-17 |
Uživatelský manuál
Philips DLP2280-17 User Manual,
2 stránky
|
| DLM75006-17 |
Uživatelský manuál
Philips DLM75006-17 User Manual,
2 stránky
|
| SJB5191-17 |
Uživatelský manuál
Philips SJB5191-17 User Manual,
2 stránky
|
| SWA3425W-27 |
Uživatelský manuál
Philips SWA3425W-27 User Manual,
2 stránky
|
| SWA3605W-17 |
Uživatelský manuál
Philips SWA3605W-17 User Manual,
2 stránky
|
| SJB4142-37 |
Uživatelský manuál
Philips SJB4142-37 User Manual,
2 stránky
|
| SJB1142-17 |
Uživatelský manuál
Philips SJB1142-17 User Manual,
2 stránky
|
| ST327000P-37 |
Uživatelský manuál
 
Philips ST327000P-37 User Manual,
4 stránky
|
| SDW5210O-17 |
Uživatelský manuál
Philips SDW5210O-17 User Manual,
2 stránky
|
| SRU9600-37 |
Uživatelský manuál
Philips SRU9600-37 User Manual,
2 stránky
|
| SJM2300H-27 |
Uživatelský manuál
Philips SJM2300H-27 User Manual,
2 stránky
|
| SPP3204WA-17 |
Uživatelský manuál
Philips SPP3204WA-17 User Manual,
2 stránky
|
| DLA1254D-17 |
Uživatelský manuál
Philips DLA1254D-17 User Manual,
2 stránky
|
| SDJ4701-17 |
Uživatelský manuál
Philips SDJ4701-17 User Manual,
2 stránky
|
| SDW5002O-17 |
Uživatelský manuál
Philips SDW5002O-17 User Manual,
2 stránky
|
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais